Driver Installation - DEC PATHWORKS v4.1 for DOS
  ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

  Siemens OfficeLAN PCI 10/100 TX Fast Ethernet Adapter

  DOS NDIS2 Driver for DEC PATHWORKS v4.1 for DOS
  INSTALLATION GUIDE


=============================================================================
CONTENTS
=============================================================================

*  Important Considerations

*  Files Provided

*  Device Driver Installation Guide
        Automatic Installation Using the NETSETUP Utility
        Manual Installation

=============================================================================
IMPORTANT CONSIDERATIONS
=============================================================================

*  This driver supports Siemens OfficeLAN PCI 10/100 TX Fast Ethernet
    Adapters.

*  This driver conforms to the Network Driver Interface Specification (NDIS)
    v2.0.1 defined by Microsoft/3Com. The driver has been tested with
    Microsoft LAN Manager, 3Com 3+Open, IBM LAN Server, IBM PC LAN
    Program, DEC Pathworks, and other NDIS-compatible network operating
    systems and protocol stacks.

*  The PROTOCOL.INI file contains configuration information.

=============================================================================
FILES PROVIDED
=============================================================================

*  L100.DOS           DOS NDIS2 driver

=============================================================================
DEVICE DRIVER INSTALLATION GUIDE
=============================================================================

*  Installing the DOS NDIS2 Driver Automatically

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

NOTE:  You must start the Pathworks scheduler (SCHK) with the switch /N.
              If /N is not used, initialization may fail. If this happens,
              the following message:

              No NDIS Interrupt Activity.  Maybe NI_IRQ set wrong or cable
              not attached or hardware/DLL broken.

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

The instructions that follow describe automatic installation of the DOS
NDIS2 Driver on PATHWORKS for DOS v4.1 using the NETSETUP utility.

If you install PATHWORKS for the first time or update it using the
NETSETUP installation program, you get the following prompts and
your responses must be as shown below.

1.  Select your choices for the following:

     *  Type of configuration
     *  Destination drive (boot device)
     *  LK250 keyboard setup information

2.  Select <Ethernet> network adapter type.

3.  Select <Other NDIS> Ethernet adapter.

4.  For full DRIVE:\PATH \FILENAME for NDIS2 driver, type:

     A:\NDIS\DOS\L100.DOS

5.  For full DRIVE:\ PATH\ for the PROTOCOL.INI stub, type:

     A:\NDIS\DOS

    The files copy from the installation diskette to the appropriate
    directory.

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

NOTE:  If you update PATHWORKS using the NETSETUP installation
              program, you should rename or copy the CONFIG.SYS and
              PROTOCOL.INI files before starting NETSETUP.

*  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *  *

*  Installing the DOS NDIS2 Driver Manually

The instructions that follow describe manual installation of the DOS
NDIS2 Driver on PATHWORKS for DOS v4.1.

1.  Copy the L100.DOS file from the driver installation diskette to the
     PATHWORKS directory.

     Example:

     C:\DECNET> copy A:\NDIS\DOS\L100.DOS

2.  To load the driver, add the following line to your CONFIG.SYS file:

     DEVICE=<drive>:\DECNET\L100.DOS

  3. Using a DOS editor, copy the PROTOCOL.INI stub from the driver
      installation diskette to the end of the old PROTOCOL.INI file.

      Example:

     [L100]
     DRIVERNAME=L100$

  4.  In the PROTOCOL.INI file DATALINK and IPX4MAC modules,
       change the value of the keyword BINDINGS from:

       BINDINGS = driverlabel

       to

       BINDINGS = L100

=============================================================================

This software and documentation have restricted rights: their use, duplication,
or disclosure by the Government is subject to the restrictions in:

*  DFARS 252.227-7013
    Subparagraph (c) (1) (ii)
    Rights in Technical Data and Computer Software clause

*  FAR 52.227-14
    Alternate III
    Rights in Data -- General clause

*  FAR 52.227-19
    Subparagraphs (c) (1) and (2)
    Commercial Computer Software -- Restricted Rights clause


Other product and company names are registered trademarks or trademarks of
their respective holders.