6 Windows NT 3.51 with NT Requester
                                                                    v1.03


Windows* NT* 3.51 and NT Requester client driver installation notes for
Intel's EtherExpress(TM) PRO/100B adapter
=====================================================================

Location of driver: \NWSERVER\E100B.LAN
                    \NWSERVER\OEMSETUP.INF

The installation of Novell's NT Requester using the E100B.LAN server
driver supports Windows NT 3.51.


General instructions for NetWare* Requester under Windows NT 3.51
=================================================================

1  Install the NT Requester. See the documentation that came with the NT
   Requester for instructions.
   
   Note: If the NDIS driver for the PRO/100B is installed, remove it from
         NT before installing the Netware NT Requester.

2  Start Windows NT and log in as ADMINISTRATOR (or another valid user
   name).

3  Double-click the "Network" icon in the Control Panel. The "Network
   Settings" screen appears.

4  Click the "Add adapter" button.

5  Select "Other - Requires disk from manufacturer" and click Continue.

6  Insert the Intel Configuration and Drivers Disk into your floppy drive
   and type A:\nwserver.  Click OK to continue.

7  When "ODI Intel EtherExpress PRO/100B adapter for NetWare" appears,
   click OK.

8  With the floppy disk still inserted, click Continue.

9  After the files are copied, the default driver settings will be
   displayed (they'll be displayed with their defaults which in most
   cases is OK).  Click OK when correct.
   
   NOTE: Do not click on Advanced Settings.  See the section titled
   Advanced Setting below.

   Speed: Specifies the line speed of the adapter.
             0    =    Auto detect (default)
             10   =    10 Mbps
             100  =    100 Mbps
   

   ForceDuplex:

   Note: The PRO/100B T4 adapter does not support full duplex at 100
   Mbps.  It does at 10 Mbps.  The PRO/100B TX adapter supports full
   duplex at 10 and 100 Mbps

             0 = auto-negotiate (default)
             1 = half duplex
             2 = full duplex
      
      Note: If the adapter is set to half or full duplex, set the SPEED
            parameter to either 10 or 100. (see SPEED)

   Duplex modes:

   Auto-negotiate _ the adapter negotiates with the hub how to
   send/receive packets, either full or half duplex.  If unsuccessful at
   negotiating the duplex, the adapter defaults to half duplex.

   Half duplex _ the adapter performs one operation at a time. It either
   sends or receives.

   Full duplex _ the adapter sends and receives packets at the same time.
   This improves the performance of your adapter. Set duplex mode to full
   duplex ONLY if you have a switch that supports full duplex.




   IoMapMode:  Sets the way the driver communicates with the adapter.  In
   most cases Memory map will work best.

        0= Memory map (default)
        1= I/0 map

10 Select Bus Type and Bus Number:

   Bus Type: PCI MUST be selected.  NT will report all buses that are on
   the computer.

   Bus Number: This is the PCI bus that the PRO/100B is in.  This is only
   necessary if the computer has multiple PCI buses.  SETUP.EXE provided
   on the Intel configuration and Drivers disk can be used, under DOS, to
   determine the PCI bus number

   Click OK.

11 In the Network Settings dialog box click OK to accept the
   configuration.

   Select an IPX Frame Type:

   Auto (default)

12 You will have to restart Windows NT to complete the installation.


Advanced Settings
=================

Only select Advanced Setting if you want to use local Administration of
Addressing or are using multiple Intel EtherExpress PRO/100B adapters.
Entering Advanced Setting requires that you know the slot number the
adapter is using.

1  To get to Advanced Setting from the Network Setting Dialog box
   highlight the ODI Intel EtherExpress PRO/100B adapter and click
   Configure.

2  Click Advanced.

3  There are 2 advanced options, Node Address Override and Slot.

   NODE ADDRESS OVERRIDE: Use this option to provide your own unique node
   address for the adapter.  The node address is a 12-digit hexadecimal
   number; the second digit must be one of the following digits: 2, 6, A,
   E.

   SLOT: Select the slot number the adapter is in. Only necessary if
   multiple PRO/100B adapter cards are being used.  Before clicking OK,
   you must enter a valid slot number.  To exit without saving a slot
   number, click Cancel.



* Third-party trademarks are the property of their respective owners.