ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
	    º							º
            º     Compex RL2000A PnP Series Ethernet Adapter    º
            º  Copyright (C) 1996 by PDS. All Rights Reserved.  º
	    º							º
	    ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ GENERAL INFORMATION ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 1) RLPNPA.DOS v1.0

     This NDIS driver for Windows For Workgroups 3.11
     was written to and tested with the Network Driver Interface
     Specification (NDIS) Version 2.0.

 2) OEMSETUP.INF

     This is a Windows For Workgroups 3.11 installation file
     for RL2000A PnP Series Ethernet adapters.

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE  ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

** - IMPORTANT 
     =========
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Recommended you run RLASET configuration utility first before you
    proceed with installation of LAN adapter driver described below.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note:- If you are installing more than one LAN adapter, run RLASET utility
       to configure both adapters first. RLASET will automatically configures
       the adapters with conflict free settings. Then save and proceed with
       the installation.   

 Windows For Workgroups 3.11
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ
     a) Start Windows For Workgroups 3.11.

     b) In the Network folder, choose the Network Setup icon.

     c) In the Network Setup dialog box, choose the DRIVERS button.

     d) The Network Drivers box appears. Choose the ADD ADAPTER
        button.

     e) The Add Network Adapter box appears. From the list of network
        adapters, select Unlisted or Updated Network Adapter.

     f) The Install Driver box appears. Insert driver diskette
        into floppy drive and type the path of the NDIS driver. Choose
        the OK button

          eg.     A:\WFW311
	
     g) The Unlisted or Updated Network Adapter box appears. Inside
        this box, 'Compex RL2000A PnP Series Ethernet Adapter' appears
        highlighted. Choose the OK button.

     h) In the Network Drivers dialog box, 'Compex RL2000A PnP Series
        Ethernet Adapter' appears highlighted. Choose the CLOSE button.

        Note: In the case of multiple adapters, you MUST choose the SETUP
              button and then select the ADVANCED button to specify the
              adapter number.
              Please refer to 'DRIVER CONFIGURATION PARAMETER' section.

     i) The Network Setup dialog box appears. Under the Network
        Driver list, 'Compex RL2000A PnP Series Ethernet Adapter'
        appears highlighted. Choose the OK button.

     j) The Windows setup dialog box appears. Because you are replacing
        the Enhanced Mode Protocol Manager, choose the YES button.

        
ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ DRIVER CONFIGURATION PARAMETER ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 In Compex RL2000A PnP Series Adapter Setup, users are required to
 select correct configuration parameter for their multiple network adapters
 installed in the system.

 Adapter Number - It specifies which adapter the driver is going to control.
                  Driver searches all RL2000A PnP network adapters
                  starting from 0x200 to 0x3E0 and then initializes the adapter
                  specified by this number. In the case of single adapter,
                  it should be set to 1.