ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
	    º							º
            º     Compex RL2000A PnP Series Ethernet Adapter    º
            º  Copyright (C) 1996 by PDS. All Rights Reserved.  º
	    º							º
	    ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ

** - IMPORTANT 
     =========
  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Recommended you run RLASET configuration utility first before you
    proceed with installation of LAN adapter driver described below.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

 Below are guidelines for installing the server driver, RLPNPA.LAN,
 in a NetWare v3.12 environment.

     1. Install Novell NetWare v3.12 operating system into your
        server station hard disk.

     2. Copy the server driver, RLPNPA.LAN, from the driver
        diskette into the NetWare v3.12 server station hard disk.
	     For example, type

	     C:\SERVER.312> COPY A:\NW3.12\RLPNPA.LAN

     3. Run SERVER.EXE on the NetWare v3.12 server station.

     4. At the NetWare 386 prompt, type:

             : LOAD C:NBI31X     <Enter>
             : LOAD C:MSM31X     <Enter>
             : LOAD C:ETHERTSM   <Enter>
	     : LOAD C:RLPNPA      <Enter>

     5. Bind IPX to the server driver by typing:

	     : BIND IPX RLPNPA    <Enter>

ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ COMMAND LINE OPTIONS ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 Apart from the standard command line options of PORT, INT, FRAME,
 etc, the server driver also provides an additional command line
 option for installing multiple adapters.

    1. BOARD

       Valid board number are : 1 - 4

       This option is used to specify which board to initialize
       if there are multiple boards installed in the system.
       If the board number is not specified, the driver will detect
       all the I/O ports of the boards for user to select.
     
       You may specify the board number you require when loading the
       server driver, for example:
     
	   : LOAD RLPNPA BOARD=1


ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLING MULTIPLE ADAPTERS ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 The following steps describe the method of installing two network
 adapters:

    1. Make sure that the hardware settings of the two RL2000A
       network adapters do not conflict.

    Hint:
          Install all network adapters in the PC.
          Run the RLASET configuration program. It will resolve all
          hardware conflicts on all RL2000A PnP cards in the PC.
	  Save the configuration.

    2. Run SERVER.EXE.

    3. At the NetWare prompt, type:

	   : LOAD RLPNPA

       If the I/O port of the two adapters are 280h and 300h, with
       IRQ number A and 3 set respectively, then your screen displays
       the following messages when you load the server driver.

	  Loading module RLPNPA.LAN
          Supported I/O port values are : 280, 300
                I/O port : 280           <ENTER>
          Supported interrupt number values are : A, 5
                Interrupt number : A     <ENTER>

       The I/O ports and IRQs of the adapters are AUTOMATICALLY
       detected by the server driver.

    4. To load the server driver again, type:

	     : LOAD RLPNPA

       The screen displays the following messages:
     
          Do you want to add another frame type for a previously
	  loaded board? <n>

	  Loading module RLPNPA.LAN
          Supported I/O port values are : 300
                I/O port : 300           <ENTER>
          Supported interrupt number values are : 5
                Interrupt number : 5     <ENTER>

            Previously loaded module was used re-entrantly.

    5. Bind IPX to both the network adapters.

NOTE:
     The three modules below needed to be loaded in the server
     according to the sequence:
      (1) NBI31X.NLM
      (2) MSM31X.NLM
      (3) ETHERTSM.NLM
      (4) RLPNPA.LAN.
     
     The user need not load NBI31X.NLM, MSM31X.NLM and ETHERTSM.NLM
     because they will automatically be loaded when the server driver
     RLPNPA.LAN is loaded. However the user must ensure that NBI31X.NLM,
     MSM31X.NLM and ETHERNET.NLM are in the server's search path.