ษอออออออออออออออออออออออออออออออออออออออออออออออออออป
	    บ							บ
            บ     Compex RL2000A PnP Series Ethernet Adapter    บ
            บ  Copyright (C) 1996 by PDS. All Rights Reserved.  บ
	    บ							บ
	    ศอออออออออออออออออออออออออออออออออออออออออออออออออออผ

ฺฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฟ
ณ INSTALLATION GUIDE ณ
ภฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤฤู
   This document describes the procedures for installing
   both NDIS2 and ODI drivers for LANtastic 6.0
   in Windows For Workgroups 3.11 and DOS.

1.1) LANtastic 6.0 with Windows For Workgroups 3.11
อออออออออออออออออออออออออออออออออออออออออออออออออออ
1.1.1) Setup

     a) Start Windows For Workgroups 3.11 and install a
        network adapter. Please refer to Windows For Workgroups
        3.11 User Guide for the installation procedures of
        a network adapter.

     b) Start Windows For Workgroups 3.11 again.

     c) Insert LANtastic Network Software v6.0 Disk 1 into
        drive A.

     d) In File Manager, run INSTALL.EXE in the Disk 1.

     e) Enter an UNIQUE computer name in the Enter Computer Name
        box.

     f) Select the destination drive in the Enter Target Drive
        box.

     g) Enter the destination directory in the Enter Directory
        box.

	eg. C:\LANTASTI

     h) Select the additional LANtastic features in the
        Select All That Apply box.

     i) Check the installation information in the LANtastic
        Information Check box. If an ODI driver is required,
        goto step (m).

     j) Select the NDIS Support for Network Adapters option
        in the Select Network Adapter box.

     k) Enter the full pathname for the directory containing the
        NDIS 2.01 driver in the Enter NDIS Driver Directory.

	eg. A:\NDIS2

     l) Insert Compex RL2000A-PnP Ethernet Disk 1 into the
        floppy drive (eg. A:)

     m) Check the installation information in the LANtastic
        Final Information Check box. 

     NOTE:
     -> If Extra Options shows Microsoft Client Novell Client or
        Novell Client, the Network Adapter option will be ODI Driver
        for Node Runner.

     -> If Extra Options shows Microsoft Client, the Network
        Adapter option will be NDIS Support for Network Adapters.
        Network Adapter: ODI Driver for NodeRunner

     n) Follow the instructions to continue the installation.

1.1.2) Extra Modifications for NDIS Driver Installation

     If you install the client to Microsoft network ONLY, a NDIS
     driver is required. Follow the instructions here to make some
     modifications.

     a) Use any text editor to open the setup file,
        PROTOCOL.INI in your LANtastic home directory
        (eg. C:\LANTASTI) and modify it as follows.

	...
	[NETBEUI_XIF]
	Drivername = NETBEUI$   <- Add this line
	...

     b) If the hardware settings of the adapter are different
        from that specified in the PROTOCOL.INI, please change them
        correctly.

     c) Obtain the file, NETBEUI.EXE, from Microsoft and copy it
        to your LANtastic home directory (eg. C:\LANTASTI).

1.1.3) Extra Modifications for ODI Driver Installation

     If you install the client to Novell network, a ODI driver
     is needed. Follow the instruction here to make the
     modifications.

     a) Use any text editor to open the config file, CONFIG.SYS and
        add the following lines.

	...
	FILES=50
	BUFFERS=32
	LASTDRIVE=Z
	DEVICE=C:\LANTASTI\PROTMAN.DOS /I:C:\LANTASTI
	...

	where LANTASTI refers to the directory where your LANtastic
	software is installed.
	
     b) Edit the setup file, STARTNET.BAT, in your LANtastic home
        directory (eg. C:\LANTASTI).
 
	Original STARTNET.BAT
	...
	LOADHIGH LSL
	NRODI
	LOADHIGH ODINSUP
	LOADHIGH IPXODI
	LOADHIGH AI-NDIS BIND_TO=NRODI...
	...

	New STARTNET.BAT
	...
	LOADHIGH LSL
        RLPNPA                                  <--- Change
	LOADHIGH ODINSUP
	LOADHIGH IPXODI
        LOADHIGH AI-NDIS BIND_TO=RLPNPA         <--- Change
	...

     c) Edit the config file, NET.CFG, in your LANtastic home
        directory (eg. C:\LANTASTI).

	Original NET.CFG
	...
	LINK DRIVER NRODI
		FRAME ETHERNET_802.2
	...

	New NET.CFG
	...
        LINK DRIVER RLPNPA                       <--- Change
		FRAME ETHERNET_802.2  


     d) Edit the protocol initialization file, PROTOCOL.INI, in your
	LANtastic home directory (eg. C:\LANTASTI).

	Original PROTOCOL.INI
	...
	[NETBEUI_XIT]
	Drivername = netbeui$
	...
	Bindings = NRODI
	...

	New PROTOCOL.INI
	...
	[NETBEUI_XIT]
	Drivername = netbeui$
	...
        Bindings = RLPNPA..


1.2) LANtastic 6.0 with DOS

     a) Insert the LANtastic Network Software v6.0 Disk 1 and
        execute the following command:-

	A:\>INSTALL /DOS

     b) Enter an UNIQUE name in the Enter Computer Name box.

     c) Select the destination drive.

     d) Enter the destination directory in the Enter Directory box.

     e) Select the correct LANtastic features.

     f) Check the installation information.

     g) Modify the files as described in the section (1.1.1) or
        (1.1.2) accordingly.