ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
       º                                                              º
       º  Compex FreedomLINE 100TX/10base PCI Fast Ethernet Adapter   º
       º        (C) Copyright PDS, 1998. All Rights Reserved.         º
       º                                                              º
       ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

The installation for the NDIS3 driver for Windows NT is menu driven
through the Windows NT interface. The driver and installation files are
located in the NDIS3 of this driver disk.
The guidelines assumed you have installed Microsoft Windows NT and is
installing network support using Compex FL100TX/10base PCI Fast Ethernet
adapter. 

Note: The root directory of this disk contain NDIS4 driver which is not
      support by Windows NT v3.xx. Use the NDIS3 directory to install.

This driver disk supports also the following Compex LAN adapters.
   [ Compex FreedomLINE 100TX/10Base PCI (21143) Fast Ethernet Adapter ]


ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ INSTALLATION GUIDE ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
 Installing Windows NT v3.51
 ÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ

 1.  If Windows NT operating system is being installed, select other
     manufacturers from the network adapter card option and follow
     steps 5-10.

 2.  If Windows NT operating system is already installed, logon as
     Administrator and select <Network> icon from the <Control Panel>.

 3.  Select <Add Adapter> from the <Network> window.

 4.  Select the option <<Other>Requires disk from manufacturer> from
     the <Network Adapter Card> box. A <Insert Diskette> dialog box
     appears.
 
 5.  Insert the driver diskette in Floppy Drive A

 6.  Follow the instructions appearing on the screen and enter A:\NDIS3
     asked to give the source of the driver.

 7.  A <Select OEM Option> dialog box appears. Select <OK> for FLPCI
     adapter shown in the Adapter list.

      [ Compex FreedomLINE 100TX/10base PCI (21143) Fast Ethernet Adapter ]
	
 8.  Configure the correct hardware setup of the FLPCI adapter.

 9.  Select <OK> in the Network window.

 10. Reboot the system.

 11. The NDIS 3.0 driver for Windows NT is now properly installed


ÚÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ¿
³ Optional Parameters ³
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
      ConnectionType:

      ------------------------------------------------------------------------
      Compex FreedomLINE 100TX/10base PCI (21143) Fast Ethernet Adapter
      ------------------------------------------------------------------------
           o AutoSense                     Senses dynamically the media ports
                                           Does not support 10BaseT's
                                           NO_LINK_TEST.

           o 100BaseTx                     To connect 100BaseTx Ethernet hubs

           o 100BaseTx Full_Duplex         To connect 100BaseTx Full Duplex hubs

           o 10BaseT                       To connect 10BaseT Ethernet hubs

           o 10BaseT Full_Duplex           To connect 10BaseT Full Duplex hubs

           @ 10BaseT NO_LINK_TEST          Select the 10BaseT medium with no
                                           link integrity test. Choose this
                                           option if the adapter is connected
                                           to a hub which does not generate
                                           link pulses to check the link
                                           integrity.